Blog

Simple Water Heater Maintenance Tasks

Posted by on Jan 26, 2016 in Gas Water Heater Repair Santa Barbara, Water Heater Repair Santa Barbara | 0 comments

Ready for some water heater maintenance today? It is not going to take long. . .truly we were thinking about ten minutes. You bet, that may be all it will require to cover 2 maintenance duties that every homeowner can execute. The best benefit is they will help Santa Barbara property owners with the following:Santa Barbara Water Heater Maintenance Steps

Ensuring that ones water heater survives as long as possible, conserving money.
By ensuring ones water heater works properly.
Making certain it works as energy efficiently as possible, also conserving expenses.

So with that in mind, let us educate you on how to invest 10 minutes once or two times a year to help prevent any water heater repairs for your Santa Barbara water heater.

Testing the T&P Relief Valve

The job of the temperature and pressure relief valve, also known as the T&P Valve, is extremely crucial. It has the crucial job of ensuring that too much pressure won’t build up on the inside of the storage tank, which will guarantees the water heater does not blow up. The infographic below illustrates the following actions in testing it. The lever should be raised some and then let go of it. It should snap back to its shut placement quickly. If it is performing correctly, some water is often heard going in the drain pipe beneath the lever that was just raised and the noise of some pressure discharged might be observed. One will be needing a new valve if none of these items take place during the evaluation.

Accomplishing a Mimi Water Heater Tank Flush

In time, rust and corrosion will appear on the inside of the water storage tank because of the chemical reactions taking place with the parts that are necessary to create heated water. We will not go directly into the complex chemical information in this article, but by simply draining some of the water, it helps get rid of the sediment, and supply an occasion to view what amount of sediment is within the water heater.

To complete a tiny flush, place a pail underneath the drain valve, positioned at the lower part of the tank, and open the drain valve. Just drain several gallons of water – a few pails full. Let the water sit in the final pail for several minutes. As soon as it settles, look to find out how many things has settled to the bottom part of the pail. If there is, if the water heater has actually not been drained for a long time (or ever), it would be best to do a complete flush of the tank to get as much of the sediment out as possible.

Check out how clean the water appears to be. If it does not appear very dirty simply accomplishing the mini flush is going to be okay. If there is a great deal of stuff in the water a whole flush should be executed. If you know it has not been drained for a long time, if ever, it is a good suggestion to drain it all.

We will not be going straight into all the techniques in this article to accomplish this, but for educational reasons, initially decrease all the way the temperature. Wait at least one hour to enable the water to cool down ahead of draining it. Instead of using the buckets, it is easier to attach a hose to the drain valve and drain the water outside.

If one begins to be aware of weird popping sounds from the water storage tank, it is actually a sign that there may be a sizable amount of sediment accumulating on the inside. This too reduces the energy efficiency of the water heater.

Water heaters will function quite well without the need of a great deal of maintenance, and a number of homeowners tend not to carry out any sort of maintenance to them. Nevertheless, to realize the three advantages mentioned at the start of the post, it is very important to at least carry out these 2 tasks. If you have any queries or feel like you would like some help initially, contact us! We are always accessible to aid and to help protect against an unnecessary Santa Barbara Water Heater Repair.

Water Heater Repair Santa Barbara California

From Visually.

Eliminating Water Heater Odor

Posted by on Jan 4, 2016 in Plumbing Repair Santa Barbara CA, Water Heater Repair Santa Barbara | 0 comments

When the water coming out of the taps inside the house stinks, there is probably a problem with your water heater. There might be a couple of different causes of stinky water, however the primary reason is bacteria. Whenever bacteria is entering into the water, an odor will more than likely show up. Well water is typically responsible for this transpiring. But, there are a few measures a Santa Barbara homeowner could take to prevent bacteria from expanding in their water and to get rid of present bacteria and odors.

Protecting Against Water Heater Bacteria Growth

The best way to stop bacteria from growing and bringing about bad tastes and odors in one’s property, is to make certain the temp is set at 140 degrees or higher on one’s water heater. In this temp bacteria can’t expand and will be killed. If perhaps your water heater temp is placed any lower than this, bacteria will not only exist but can grow.

According to Soquel Creek Water District, “The smell is the result of four factors that must all be present for the odor to develop. These factors include:

  • A high concentration of sulfate in the raw water
  • Sulfate reducing bacteria, non-toxic to humans (sulfate is reduced to a sulfide state by the bacteria)
  • Little or no dissolved oxygen in the water
  • Hydrogen (a component of water which may be present due to water conditions reacting with the anode)”  Read more here…

Getting Rid of Hot Water Heater BacteriaSanta Barbara Water Heater Odors

In order to remove present bacteria and smells, one will have to use harsh chemicals to eliminate it. Chlorine bleach is the most effective and comprehensive chemical cleaner to utilize. If you are making an attempt to clean out the water and get rid of the bacteria applying bleach yourself, make sure you fully understand the precise process of doing this. First, the electric or gas going to the water heater should be switched off. Next the cold water supply has to be switched off. After that, you will have to switch on one of the hot water faucets in the property. This allows air in the tank. Using a garden hose, empty the water from the water heater and close up the drain valve after all of the water has been drained. After this, it is time to pour in the bleach. One will be needing five ounces of bleach for each gallon of water the tank holds. Unscrew the flexible cold water hose and pour the bleach into the opening. If perhaps the cold water hose isn’t flexible, it may be a good idea to call in an expert. Connect the water line once more and fill up the tank with water. It’s crucial to turn off the hot water faucet in the home when all the air is out of the line. It’s likewise crucial to run each of the taps which employ hot water in the house until it is possible to smell the bleach. The bacteria that is inside the water heater might also be in piping and faucets for that reason you will need to eliminate the bacteria in these locations also. Let the bleach water remain inside the tank and inside the pipes for nearly 3 hours without using any hot water. And then an additional flush is in order. After the tank is drained once more, do not put in more bleach but fill it back up with water and allow it to sit inside the tank and inside the water lines for no less than thirty minutes. Lastly, drain the tank once more and refill the tank with water. Let all of the hot water appliances in the house drain until you can no longer smell bleach. Either flip the power on again or reignite the pilot and you will be good to go!

For any concerns about water smells, flushing a water heater, Santa Barbara water heater repairs, or any other water heater issues, call us!

Indications of a Hot Water Heater Failure

Posted by on Dec 23, 2015 in Gas Water Heater Repair Santa Barbara, Water Heater Repair Santa Barbara | 0 comments

Hot water heaters generally accomplish everything that they’re intended to and usually remain undetected until one needs a Santa Barbara Water Heater Repair. However, several of the issues which develop could be prevented by having regular servicing by an expert. Always watch your natural gas burning hot water heater, because several of the issues that might arise may be costly and harmful for family and friends and animals. In this post, we’re outlining 4 indications that a gas water heater could possibly have to be exchanged.

Leaking WaterWater Heater Repairs Santa Barbara

If perhaps there is water on the ground around your water heater or leaking from a pipe, you might want to exchange the water heater. But, based on where the water is and what amount there is, you may be all right. In case the water heater is leaking water from a pipe and there exists some water on the floor beside the unit, it’s more than likely the T&P valve. The temperature and pressure valve gets rid of unnecessary water vapor inside the hot water heater, this kind of water vapor changes to water and will come outside of the hot water heater by way of a pipe on the side of the unit. If perhaps this is the case, it is completely typical and vital for the water heater to work correctly. Never try to shift the T&P valve and don’t block it. In cases where you are concerned with the quantity of water that is coming from the pipe, contact an expert! If perhaps the leaking water is coming from the underside of the tank, it is pretty much definitely time to get a different hot water heater. When the water heater warms water the metal tank expands and contracts, this movement might result in cracks and minor fractures, which will sooner or later result in leaks. As soon as this takes place, it will be time to buy a new system.

Corrosion

Around the piping coming out of the water heater you will find pipe fittings that ought to be sealed well to be able to keep the pipe in place as well as keep water from leaking out of the opening. In the event you are seeing rust around these pipe fittings, water is seeping out of the opening. While this is not a big leak and will not likely lead to immediate harm to the hot water heater, if the issue isn’t solved, major and expensive complications can eventually arise.

Burn Marks

In cases where you’re finding burn marks on the base of the water heater, there can be two potential problems. But, both are really critical and both will need an expert. One problem can be with the venting. In the event the venting is clogged or was mounted incorrectly, it can cause the exhaust gases to come back in the property. This is hazardous and might result in health issues or a fire when left unnoticed for long. But, it may not indicate you must replace the water heater, and that is good. Another possible problem with burn marks might be the flue pipes in the water heater are obstructed. This could result in numerous hazardous problems and, regrettably, the hot water heater will have to be swapped out as quickly as possible.

Yellowish Flame Color

Gas hot water heaters have a blue flame below the tank when it is running. But, if you’re seeing the flame is an orange or yellow color, as opposed to blue, the burner is not working appropriately and will have to be looked at by a professional.

There are numerous issues which can develop with natural gas burning water heaters, however together with frequent upkeep and yearly check ups, you may be able to prevent the need for an unexpected water heater repair in Santa Barbara that could possibly be costly. Call us today in case you observe something out of the ordinary with your water heater!

Total Water Heater Maintenance Tasks

Posted by on Dec 17, 2015 in Gas Water Heater Repair Santa Barbara, Water Heater Repair Santa Barbara, Water Heater Replacement Santa Barbara | 0 comments

Certainly one can find plenty of unlucky testimonies that homeowners have about water heater maintenance of “waking up to the cold shower.” Well, we are not going to look at how miserable of a circumstance that may be. Additionally, we will presume that one realizes the basic idea of ensuring that ones water heater is maintained systematically to be able to receive the best from its life, and to make sure an emergency Water Heater Repair in Santa Barbara is not needed. This will help one spend less on power bills also. All of that is wise we understand. While not needed a lot of maintenance, hot water heaters will need some. We are astounded, although not shocked, by the amount of clients we see who have not done any kind of upkeep to their water heater), below are the tasks one should be aware of concerning maintenance.

The Probable Length of Time a Santa Barbara Water Heater Should LastHot Water Heater Repair in Santa Barbara

8 to 10 years is the typical amount of time a standard gas water heater can last. There are several factors that will have an effect on the all around lifespan needless to say, however this is a good standard. Perhaps the largest element which will impact the long life of it is actually mineral deposits. The steps discussed here are presented in hopes of helping to reduce the accumulation of mineral deposits inside of the storage tank of the water heater.

Methods to Reduce a Santa Barbara Water Heater Repair

Homeowners, even individuals which usually do not feel too handy, are capable of doing lots of water heater maintenance by themselves. However much of the time, a water heater will run safe and sound, keep in mind that they actually operate off of electric power and/or gas. Consequently suitable safety measures ought to be observed by Santa Barbara homeowners. Be sure to make use of these techniques as an instructional guide, for we’d much rather demonstrate all these together with you directly.

First, the water heater’s power requires to be turned off before accomplishing any routine maintenance. Ones breaker box should have a switch labeled that point outs which breaker goes to the water heater. House owners who have a gas water heater, move the gas cutoff counterclockwise in order to shut off the gas.

Anode rods, or often known as sacrificial anode rods, are the portion of the heater that helps with avoiding rusting within the water storage tank. Almost all are composed of aluminum while some are constructed of magnesium around a steel wire. With time the external covering of the rods will wear away and they ought to be replaced when the steel wire is noticeable. They typically last around 5 years, though that may be shortened if ones water is soft. In the long run, it is better and more affordable to have the anode rods replaced, so that one can acquire an extended life from the water heater storage tank. The rods should be looked at on a yearly basis.

Check out the subsequent video which demonstrates the technique of changing the anode rods:

The next water heater piece this article will examine are the dip tubes. Not every water heaters possess them however. They should be reviewed every 6 months for corrosion. To check it, take it out and check its length to the height of the water heater. It ought to be about 6″ to 8″ shorter as compared to the storage tank. It will need to be changed if it’s smaller than that, or shows symptoms of breakage or crumbling.

Sorts of water heater flushes. Once again, mineral deposits are the leading reason of water heater malfunctions. Just how fast sediment establishes inside the storage tank is determined by the quality of ones water. Over time, this sediment can solidify, leading to weird noises from the storage tank, lessen the efficiency of the device, and maybe clog the drain valve. If possible, every six months, but at the least yearly, drain 1 or 2 gallons of water from the drain valve at the bottom of the hot water heater into a bucket or by a garden hose in a bucket outside. Look to check out what amount of sediment is in the pail after the water settles. If it seems to be relatively clear, that is good! If these kinds of small flushes are undertaken 2 times per year, one will possibly not have to perform a big flush as often. If the water looks very cloudy, a full flush should be executed. It is also a great time to make sure the bottom drain valve of the storage tank is functioning properly and not leaking. They are generally made of plastic and with time when they aren’t opened up, they are going to get stuck or not close up properly, and that’s why it truly is advisable to open and close them throughout the small flush test.

The flushing procedure will help with removing hot water smells that can happen too.

The advantages for flushing a water heater are illustrated in the following video:

For all those that possesses vacation homes or temporary residences, one will need to empty the storage tank of all its water to help prevent any flooding during the periods the dwelling is not lived in. Naturally, ensure to refill it when the dwelling is to be resided in once again.

Inspecting water pipes. Examine to make certain all water pipes do not have leaks or are harmed in any way. This should be easy to notice if there are any leaks coming from any section of the water pipes or storage tank for it will have water below and/or around the unit. Leaking water may cause water damage to areas of ones house, so be sure all looks dry, especially if the heater is situated inside the residence and not in a garage.

Checking the T&P valve. Yearly, the T&P valve, or temperature and pressure relief valve, needs to be examined. The T&P valve’s job would be to safeguard the water heater storage tank from extra pressure, and exploding. The owners handbook needs to be looked over to be sure the proper ways are followed but here are the basic measures. A little water may come out of the valve and it’s going to be extremely hot so be careful. Raise the handle and let go of it. Have a container prepared to catch any unwanted water that may come out. Additionally, the noise of pressure getting discharged will be noticed. The lever needs to snap back in position. In the event that it does not try it again. When after a few attempts it will not go back into position, a new valve will be needed. The valve might drip a little water afterwards for a short period. If it fails to stop dripping after a few hours inform us.

Throughout the years, a great deal of debate has occurred on precisely what the best temperature should be for any water heater. Producers generally pre-programmed heaters to 140 degrees, which is indeed hotter than almost all people definitely will ever require it to be. 120 degrees is the common temperature and some individuals also go as low as 100 degrees. We have been writing much more on this, however we would suggest having the temperature close to 120 degrees.

Tips For Gas Water Heaters

Every three months is a good time to examine the gas venting system. All the fittings should be looked at to verify they’re not lose, look for blockage, and search for damage to the vent piping, and also making certain they’re free of rust and deterioration .. Fumes are vented to the outside of the household with gas fired heaters. If these gasses make their way in the home it could be poisonous and a fire hazard. Ensure everything flammable or corrosive is clear of the exhaust venting to assist in preventing fires. Any loose, damaged, or corroded portions of vent piping should be updated.

Look at the pilot light to conduct a visual assessment of how it is working. The purpose of the pilot light will be to fire up the gas burner that heats water for the house. For any water heater to run at prime performance, it is essential for the pilot light to be thoroughly clean. The flame color should really be blue for natural gas heaters. For propane heaters, the flame should really be blue/green with only a little bit of yellow at the tip. A weakened flame, a yellow flame, or a flame which has a divided flame on top indicates that an adjustment is required.

Tips For Electric Water Heaters

Utilizing insulation wraps or covers around the storage tank can certainly help preserve a regular temperature inside of the storage tank without needing as much electric power. Moreover, by the heater not needing to operate as frequently will lengthen the life of the heating element seeing that it will not be used so much. Occasionally, verify the insulation wrap to verify it is still attached and hasn’t slipped or shifted on the water storage tank.

Occasional assessment of the heating element is really important and will help lessen the need for an unexpected emergency repair. We aren’t going to get into the details for a total inspection at this point, however one will require a voltage/OHM meter to guarantee there exists a closed electrical circuit. Heating elements do need updating from time to time.

The area close to a water heater requires to be thoroughly clean of dirt. Specifically if the water heater is found in the garage, make sure to give the place a good sweeping often. Ones heater will run significantly better and be less likely to need a Santa Barbara Hot Water Heater Repair if it stays clean.

Replace Old Water Heaters With Energy Efficient Ones

Nowadays, most all water heaters produced possess a nice volume of energy efficiency. As of April 2015, high efficiency rules were established in the United States for water heaters. Naturally, the better the heater, the longer the life one will receive from the unit with the right routine maintenance over time. Don’t hesitate to call Water Heater Repair Santa Barbara to discuss water heater maintenance or perhaps to answer any queries on deciding on the most proper replacement water heater for ones home or office. Brand, model, and size really need to all be considered throughout the selection process and not merely implement the “bigger the better” saying. Pertaining to storage tank water heaters, it is a waste of energy to have lots of extra water being continuously heated to a hot temperature if it is not going to be made use of.

Repairing a Noisy Water Heater

Posted by on Mar 17, 2015 in Gas Water Heater Repair Santa Barbara, Water Heater Repair Santa Barbara | 0 comments

Water Heater Repair Santa Barbara is consistently being consulted to check out at water heater. Popping and knocking noises may be caused by problems with the water heater, but it’s likewise an aggravation. We are going to examine the most typical reason your water heater may possibly begin creating noise and what you can possibly do to calm it down! Prior to consulting a Santa Barbara professional, look into one of the most typical water heater issues and remedies.

The most likely reason a water heater creates noise

Again, if the sound is an warning sign of an issue with the heater that issue is more than likely sediment build up. The sediment originates from the water in the storage tank. It is primarily composed of calcium and magnesium debris and is primarily an issue in households which may have hard water.

If the sediment starts to accumulate at the bottom of the storage tank, it traps a little part of hot water below it. This triggers the hot water to boil as the tank operates. The sounds noticed are the bubbles popping through the sediment.

Also, the sediment itself might be the reason for the sounds. The sediment sits at the bottom of the tank and can get burnt up leading to odd sounds. And sometimes, the sediment will get carried up to the top of the tank and breaks off leading to sounds as it descends back down, bumping the sides on its way.

How to avoid a water heater from creating noise

If sediment build-up is what’s triggering the sounds, the heater should be looked at. Water Heater Repair Santa Barbara CA can accomplish this and provide the tank a flush or advise a different resolution.

You can also avert sediment build-up by having expert routine maintenance carried out on the storage tank approximately annually. This technique involves flushing the tank of any sediment.

A further excellent solution is to add a water softener in your Santa Barbara residence. Water softeners eliminate minerals from the water prior to it entering the water heater, drastically minimizing sediment build up.

To find out more about other probable difficulties and remedies provide Hot Water Heater Repair Santa Barbara a phone call!

Leaking Santa Barbara Water Heater Pressure Relief Valve

Posted by on Dec 9, 2014 in Gas Water Heater Repair Santa Barbara, Water Heater Repair Santa Barbara | 0 comments

The pressure relief valve of a water heater has an essential job – making sure the water heater tank does not blow up. So with that in mind, Water Heater Repair Santa Barbara wishes to see to it house owners are aware of ways to best take care of it. They will certainly leak when the valve wears out or when the water storage tank pressure gets greater then the relief point.Hot Water Heater Repair Santa Barbara

We advise that a minimum of two times a year, homeowners test to ensure the pressure relief valve, or T&P valve as we will call it, is working correctly. All one has to do is raise the manage for a few seconds and let go of it. It must snap back to its initial position. When it is raised, one may hear the noise of pressure being released from it, similar to the sound of air coming out of a tire pump when being detached. Also, a little water might come out as well. Both are normal. If the valve has not been tested for a number of years, it may stick at first too.

However, if the handle does not snap back, or if it continues to leak some water, that is not regular. If it still leakages some, raise the handle a couple of more times to see if it does re-seat itself. You could wish to wait a day or so it see if it re-seats itself prior to assuming it has to be changed.

Hot Water Heater Repair Santa Barbara would prefer to deal with any T&P valve replacements for you, so though water heaters are typically relatively maintenance free, there are some safety precautions one need to bear in mind. With that in mind here is an overview of a pressure relief valve replacement.

1. The gas to the water heater needs to be switched off, or the breaker for an electric water heater.
2. The cold water cut-off valve needs to be closed .
3. The valve below the T&P valve has to be opened to drain some water in order to relieve some of the pressure in the storage tank.
4. The overflow pipe of the T&P valve has to be taken off. It might need to be cut off if it is soldered or firmly glued.
5. The pressure relief valve has to be unscrewed with a pipe wrench.
6. Wrap the new T&P valve with Teflon tape and screw it back in place. See to it the overflow pipe opening is placed away from the storage tank.
7. Reattach the drain pipe, also utilizing brand-new Teflon tape.
8. Turn the water back on, and examine your work for any leakages.

The following video gives a summary of this process:


Holiday Santa Barbara Plumbing Advice

Posted by on Oct 29, 2014 in Plumbing Repair Santa Barbara CA, Water Heater Repair Santa Barbara | 0 comments

The holiday season is one of the busiest times of the year for us, particularly with drain cleaning, toilet repairs and other plumbing repair works. with the increased amount of guests and family in ones home, it can take a toll on the plumbing system.

Santa Barbara hot water heaters are working overtime with the added number of showers begin taken, garments being cleaned, and dishes being washed or run through the dishwasher. We recommend waiting a little bit between showers if several are to be taken back-to-back. The same goes with picking times to run the dishwasher and washing machine as well.

Drains particularly have it hard, for we are carrying out Santa Barbara drain cleaning far more frequently, with the added amount of people utilizing ones plumbing. It is also a fascinating time to see the number of toys and things that kids accidentally attempt flushing down the toilet too!

Below is an infographic that will certainly provide some recommendations on how to handle ones water heating and plumbing this holiday season.

Water Heater Repair Santa Barbara

An Overview of Four Basic Plumbing Issues

Posted by on Jun 19, 2014 in Plumbing Repair Santa Barbara CA | 0 comments

We are able to assist with any Plumbing Repair Santa Barbara CA issue one be having.  Nevertheless, it’s also a good idea to see to it you have the skills to deal with any smaller sized plumbing issues that may turn up throughout a time when it can be even harder to get a plumbing repair tech to ones home. Here are 5 easy plumbing repairs one might simply have the ability to look after oneself.

Broken Pipes

Water Heater Repair Santa Barbara

A broken pipe can cause many people to be over anxious, however take a deep breath prior to finding the main water line and turning the supply off, one might well find oneself much less stressed. Now in this case, one will have to get a plumber out to address the actual problem.

Blocked Toilet

Typically this is as basic a job as buying a low-cost plunger and getting busy with it in the u-bend. If one discovers the plunger isn’t enough to move the clog away, there are other options. Plumbing wire will permit you to obtain right in where the plunger can not go and loosen what has to be moved, while a drain snake will offer one a more comprehensive cleaning option too.

Leaky Faucets

Easily among the most usual plumbing problems property owners will certainly face, but one that is usually as easy as changing an old washer. First of all, turn off the water at the mains, then, holding the spout of the faucet, unscrew the nut that holds it in place. Next, get rid of the washer, pop on the new one and see to it you secure the bolt tightly. You should find in most cases this is enough to fix the problem.

Congested Sinks

Whether it is the restroom or the kitchen, it’s really simple for a sink to get clogged up. If it’s the former, it’ll likely be as basic as removing hair, however in the latter, food can make its means into the pipes and cause a genuine problem. Similar to toilets, a plunger or plumbing wire will typically sort it, nevertheless one could likewise want to get under the sink and get rid of the pipe. Simply be careful to clear the area as it could get a bit wet when one does.

Home emergency plumbing repair coverage is constantly a good idea for the bigger things, however a little preparation could be all you require for a few of the smaller jobs around our home.

Santa Barbara Home Spring Maintenance Tasks

Posted by on May 12, 2014 in Plumbing Repair Santa Barbara CA, Water Heater Repair Santa Barbara | 0 comments

Right here are a couple of different maintenance jobs to carry out around your house in the spring from Water Heater Repair Santa Barbara.   Many of these tasks will not take long to do and will help rather a bit in preserving the value of ones home, as well as making it more energy reliable.

Water HeaterWater Heater Repair Santa Barbara
The average life span of a water heater is from 8 to 12 years. It’s good to check to see if there is any leaking or rusting at the system’s base, and if there are any leaks due to rust, it is a good indication that the water heater will need to be replaced unfortunately. In areas with hard water, it may be necessary to drain the water heater to get rid of sediment buildup in the tank. This need to be done two times a year to keep the heater working successfully. It also helps make it run quieter too!

Plumbing
With leaking faucets, change washers as required, even if your feline likes to sit in the tub and leisurely lick the leak. And always remember to examine for under-sink and dishwasher leaks– and repair as essential. While it’s springtime and not hot enough for you to sweat doing these duties– ensure your pipes are not either. In addition make certain your drains are running easily and your cleaning machine hoses are not protruding, cracked, or damp.

Outdoor Faucets
If you have actually drained and turned off outside faucets for winter, turn them back on and prime if needed. Inspect for leaks around turn-off valves.

Refrigerators
Your fridge is one of the most significant electricity eaters in the house– so ensuring that your door seals are airtight is very important. To test this, close the door over a dollar expense and if you can easily pull it out, the door latch could need readjustment or the seal may require changing. Believe it or not, a tiny bit of air leakage can lead to greater energy expenses. And it’s also a good time to clean the back coils as that’s an additional reason for ineffectiveness. Now go stock up on food, treat yourself, as a complete fridge and freezer uses less energy than an empty one.

Storm Windows and Screens
The radical modifications in temperature level in between winter and spring can damage caulking or rubber seals around your house’s windows and outside doors. Take time and look– it’s a simple fix and your energy bills will show the time invested. If you have removable storm windows– take them off, clean, and store them and change with screens. And do not forget to patch holes in door and window displays– to stay out mosquitoes and other small biters.

A/C Units
Examine portable AC units to see to it they are working and filters are cleaned– warm weather will come sooner than you think. An a/c not just cools you down, but a reliable air conditioner minimizes wetness and humidity from the home, which can actually damage the foundation if left unchecked. Get in the practice of altering or cleaning the filters of both a central system and portable devices once a month as dust and dirt minimizes efficiency. Central AC systems need that the hose connections are not leaking and the drain pans are draining properly– so inspect those. If a condensate drain hose ends up being clogged, it could be a build-up of algae. If this holds true, make use of a wet-vac to suck out any obstruction. And while you’re at it, clean out the ducts also.

 

 

Water Heater Repair Santa Barbara CA Video Overview

Posted by on May 3, 2014 in Plumbing Repair Santa Barbara CA, Water Heater Repair Santa Barbara | 0 comments

Below is a copy of our newest company video summary for Water Heater Repair Santa Barbara we wish to share with you today. Besides dealing with damaged water heaters, we are a full service plumbing repair company as well. We can take care of any residential or commercial repair, service, installation, and replacement plumbing situation that has to be inspected.

If you ever experience any sounds originating from you water heater, bad odors from the water, or any wetness or leakages around it, don’t wait to give us a call! These are indicators that water heater maintenance is needed, which will prevent larger problems down the road. Water heaters are generally upkeep free compared to other home appliances, but in order to get the most out of the system and to have the heater run as effectively as possible, regular upkeep is needed.